Duff-Norton Railroad Jack, 10 Ton (1022)

Rent a Duff-Norton 1022 10 ton railroad jack in Brooklyn: all-mechanical, aluminum housing, 22 in tall with about 12 1/2 in of lift. Ratchets up and down one notch at a time.

Call 718-344-1474 or request a quote. Delivery to all five NYC boroughs.

Category:

Duff-Norton 10 Ton Railroad Jack Rental in Brooklyn, NYC

American Tool Rental rents the Duff-Norton 1022 railroad jack, a 10 ton all-mechanical ratchet jack for riggers, millwrights and contractors who need to raise a heavy load a few inches at a time and have it stay put. There is no hydraulic fluid to leak and no seal to let go, so the pawl holds the load at each notch. Pick it up at our Brooklyn yard or have it delivered with the rest of your order anywhere in the five boroughs.

You work it with a steel bar in the lever socket. Each stroke raises the rack one notch, and the pawl locks it there. Flip the reversing lever and the same strokes lower the load one notch at a time, so it comes down under control instead of dropping. The cast aluminum housing keeps it light enough for one person to carry into a basement, up a loading dock or along a rail.

Duff-Norton 1022 railroad jack specifications

Make and modelDuff-Norton 1022 railroad jack (ratchet type)
Capacity10 tons (20,000 lb) on the cap, 5 tons (10,000 lb) on the toe
HousingCast aluminum alloy
Closed height22 in
Lift (rack travel)About 12 1/2 in
Lifting toeYes, 5 tons, for loads close to the ground
OperationRatchet raise and ratchet lower, reversing lever
WeightAbout 48 lb

Height, lift and weight are Duff-Norton’s figures for the 1022.

Good jobs for the Duff-Norton railroad jack

  • Raising machinery to slide in rollers, skates or cribbing
  • Lifting a beam, girder or floor joist to set shims or a post
  • Leveling heavy equipment, tanks and transformers
  • Lifting rail, rail cars, frames and machinery bases with the low toe
  • Rigging jobs where hydraulic jacks could leak or creep

Will the 10 ton railroad jack fit your job?

Use the cap when you have about 22 in of room under the load. When the load sits low, slide the toe under it instead. Set it on a solid, level base or a steel plate, never on soft ground, center the load on the head, and build cribbing under the load as it rises. For low, slow fine adjustment under 5 tons, the 5 ton screw jack is easier to dial in. To hold a ceiling or beam up for days or weeks after you lift it, set adjustable post shores. To move the load once it is up, add a 4-wheel dolly or our pallet jack. See all our jacks for rent.

Rental Details

Equipment typeJacks
Rental periodsDaily, weekly, monthly
Pickup181 2nd Ave, Brooklyn, NY 11215
DeliveryAll five NYC boroughs
RatesCall 718-344-1474
AvailabilityCall or request a quote
Ready to rent the Duff-Norton Railroad Jack?Call 718-344-1474 or request a quote

Duff-Norton railroad jack rental questions

How much can the Duff-Norton railroad jack lift?

10 tons, or 20,000 lb, on the cap, and 5 tons, or 10,000 lb, on the toe. Never go over those ratings. Center the load on the head and do not side-load it.

How do you lower a railroad jack under load?

Flip the reversing lever and keep pumping the bar. The jack steps down one notch per stroke, so the load comes down slowly. Keep your body clear of the bar, because it carries the load on every stroke.

Is a railroad jack better than a hydraulic jack?

For holding height, often yes. The pawl locks the rack at each notch, so there is no seal to wear and leak down. A 10 ton bottle jack fits lower spaces and pumps faster, but it has a much shorter stroke.

What do I pump it with?

It works with a steel operating bar that fits the lever socket. Take the bar out of the socket whenever you are not pumping, so it cannot kick back if the load shifts.

Is it the same as a Simplex RJA1022?

It is the same type and size. The Simplex RJA1022 is also a 10 ton aluminum ratchet-style railroad jack, about 22 in tall with roughly 12 in of lift. If your plan or rigging list calls for an RJA1022, this jack matches its rating.

Is a railroad jack the same as a ratchet jack or track jack?

People use all three names. A railroad jack is a heavy ratchet jack that lifts one notch per stroke of a bar. It has a low toe for lifting rail, frames and machinery bases close to the ground, plus a cap on top for loads with more room under them.

Can I work under a load on the jack?

No. A jack is for lifting. Before anyone reaches under the load, set cribbing or post shores and lower the load onto them.

Duff-Norton Railroad Jack, 10 Ton (1022) delivery in NYC

We deliver from our yard at 181 2nd Ave, Brooklyn, to job sites in all five boroughs. Call 718-344-1474 or request a quote.

Also delivering to

Renting in Brooklyn since 2000

What our customers say

on Google · 28 reviews
  • “We use them seasonally for a scissor lift to get to a 2nd story planter in the middle of Times Square. The work must be done on the weekend and they are very accommodating with drop off and pickup.”

    Sam K. · Scissor lift, Times SquareGoogle review
  • “I was unsure about renting, but this company made it so easy! The staff was patient and walked me through everything. The equipment was clean and worked perfectly.”

    NC · First-time renterGoogle review
  • “Number 1 to get generators and lifts. We rent all our tools from here.”

    Ismael R. · All Boro PlumbingGoogle review